AAR SLR15 AR15 / M16 / M4 / AR308 Armorer Course, TacOps East Conference, Arlington VA

Greg "Sully" Sullivan

Too Established
Vendor
VIP
SLR15 AR15 / M16 / M4 / AR308 Armorer Course

When: September 5-6, 2024

Where: TacOps East in Arlington VA.

We conducted a 2-day (16-hour) AR15 / M16 / M4 / AR308 Armorer course at the TacOps South conference in Arlington. This was the tenth time teaching at the TacOps conference in Arlington, and we look forward to next year as well. The training room was set up to allow plenty of table space, the lighting was better this year as compared to years past, but conferences rooms could use better lighting to help see small parts. The room was set up with a large screen which allowed us to show project animated graphics of the weapons system and powerpoint of detailed pics of gun parts, especially when looking at finer detail things like machining, stress cracks & wear.

The student base was a mix of Law Enforcement Officers from all over Virgina, Pennsylvania, Maryland, Rhode Island, North Carolina, Delaware, Kentucky, DC, West Virginia. and several Federal Alphabet Agencies were also represented.

Rifles represented in this course were SLR15, LMT, Bushmaster, Colt, LWRC, DPMS, Aero Precision, BCM, Ruger, Daniel Defense, IWI, Wyndham Weaponry, Aero Precision, Anderson, , Smith & Wesson, Sig Sauer and a few custom builds.

Day-1 started the day by going through the course manual that all students are given. Students were supplied with their own set of basic tools that are necessary to do 95% of the work on their rifles (short of restocking and rebarreling, of which wrenches and sometimes fixtures are necessary), Slip2000 "EWL" Extreme Weapons Lubricant and #725 Cleaner Degreaser, etc. A short session of nomenclature was covered, at which time covered every feature and exterior piece of the rifle to include all the hidden design features that most people are not aware of, and everyone prepped the rifles for disassembly work. Everyone was taught the procedure series of checks that we recommend.

Everyone was taught our recommended way to field strip a rifle, and why we do it this way so as not to cause damage, premature wear or stress on anything. We covered maintenance of where and what to clean, and what needs lubrication to keep it running. We showed why not to use the firing pins as tools. We showed everyone our recommendation of how to remove fouling and why, and everyone got to use our methods.

The entire bolt carrier assembly was covered, to include inspections, maintenance, upgrades, 3 types of gas rings, and differences in finishing and machining. carrier key (gas key) installation and staking, ejector systems, etc. Everyone was introduced to the different types of gas rings. We went through what each types does, and their proper installation order. Bolts were fully gone through, which included extractors, extractor springs/inserts/O-rings. The ejectors were removed, cleaned, and inspected.

Note: We went through proper carrier key staking. Several people found their gas keys were lightly staked. We supplied everyone with a MOACKS and Sully Gas Key Staking Tools, everyone decided to use the Sully Gas Key Staking Tool and get things corrected.

Note: One Officer with his Colt M4 forgot to put his firing pin back in his bolt carrier assembly, then installed it into the firearm and proceeded to perform the series of function checks that we recommend. He locked his action up so it couldn't be manually cycled. Upon inspection, I found his firing pin on his table, which is a clue as to why it is jambed up, being that the cam pin had rotated and nothing would budge. I have him a different rifle to work with while I played with it while continuing to teach the course. I couldn't get it to budge to unlock, so I decided that I would go after the cam pin through the gas tube hole. When I removed the handguards to get at the gas tube, I discovered that the barrel nut was loose, and the only thing holding in from spinning was the gas tube. So when I kicked the class loose for lunch, the Officer stuck around and I had him remove the gas tube, then remove the barrel (you could spin the Delta ring assembly by hand with no wrench required). The barrel was found to have been mounted with no molybdendum paste either. So I had him rebarrel the rifle, to include the molybdendum paste, torque the barrel nut, and get things properly indexed. By the way, once I removed the gas tube, I was able to get the cam pin to rotate and line up so I could manually cycled the bolt carrier assembly away from the barrel extension lugs.

We got into the lower receiver assemblies, starting with the fire control group (trigger group). We teach this in a building block format, starting with baby steps of getting things out and in, then build into how things work. Everyone learned how to install and remove things so you don't cause damage. We went through detailed inspections of all the sear engagement surfaces, spring types, single stage, and two stage trigger systems.

At the end of the day everyone put their rifles back together, making sure that everything was in proper working order.

Day-2 started with a review of everything that was covered on day-1, with some greater details and myths covered. We then went back into trigger groups in great details, covering single stage, 2-stage, good and bad triggers, differences and options in spring systems, diagnosing problems when semi-auto turns into burst, and showing the differences in quality of triggers that are on the market. Once done with semi-auto trigger systems, we went into select fire trigger groups covering full-auto and burst trigger groups, to include replacement and diagnosing and repairs when experiencing malfunctions.

After trigger systems, we went through the rest of the lower receivers. Everyone had collapsible stocks. We covered the proper mounting & gauging, and proper castle nut staking on the collapsible stocks, and there were a few that had to be remounted to get them properly indexed, and a hand full of them needed to be staked.

Everyone stripped their lower receivers, which allowed a chance for further inspections, and we went through a session on troubleshooting. Once everyone was comfortable with the entire lower receiver assembly, the were put back together, inspected, and made sure everything is in proper working order.

We then got into a session on the timing. This is where we cover proper cycling, covering what effects timing, and how & what happens when it is out or proper time, dwell time, suppressor issues, etc, and how to get things into proper timing. This also led us into piston systems. We covered how the piston system works, break down and maintenance of the system (Yes piston systems do get dirty and have to be cleaned and maintained), how to properly adjust for timing changed, and trouble shooting. We also covered dwell time, and how it pertains to cycling issues, and hopefully got the point across of why we do not recommend barrel lengths shorter that 11.5" on unsuppressed rifles.

Note: During the timing session, we showed examples of adjustable gas blocks, and we also showed the gas control system from https://www.riflespeed.com/, which we like as it is adjustable with a quick turn by hand to one of the 12 different settings, and is well built for durability.

We showed how suppressors are properly mounted and gauged. Several people took advantage of the bore gauges that we make, and checked their alignment on their rifles that had suppressors.

The last half of day-2 was spent on the upper receiver assembly. We covered barrel removal, mounting, fixturing, gauging & inspections. We show numerous ways to fixture a barrel into a vise, and our preference as to which fixtures/methods to use when and how. We showed how to mount, then properly torque and gauge the barrel system, which ensures it is in proper working order.

At the end of the day everyone put their rifles back together, everything was inspected and gauged to make sure it was in proper working order. Everyone did chamber inspections, checked & gauged the four gas seals, firing pin protrusion, trigger press, and headspace.

Here is a brief overview of a few things that were covered:
History of the Weapon
Cycles of Function
General Disassembly & Assembly
Identification of Common Problems and Parts
Nomenclature
Identification of Group Components
Semi, Burst, and Full Auto Parts and Conversions
Complete Armoring Disassembly / Assembly
Barrel Replacement
Cleaning and Maintenance
Sight and Distance Considerations
Ballistic Issues
Barrel: Twist, Length, and Profiles
Gas Systems & Piston Systems
Parts Interchangeability, including Brands
Headspace
Firing Pin Protrusion
Trigger Systems
Chamber Inspection and Issues
Troubleshooting, diagnosis & repair
Gauging, Inspections, Stress & Interval Issues
Accessories and Customizing
Tool Options and Selection
SOP/MOD Accessories and Additions


CY6
Greg Sullivan "Sully"
WeaponsArmorer
SLR15 Rifles
TheDefensiveEdge.com

(763) 712-0123
 
Top