AAR SLR15 AR15 / M16 / M4 / AR308 Armorer Course, Harrisburg PA

Greg "Sully" Sullivan

Established
Vendor
VIP
SLR15 AR15 / M16 / M4 / AR308 Armorer Course

When: February 9-10, 2023

Where: Harrisburg, PA

We conducted a 2-day (16-hour) AR15 / M16 / M4 / AR308 Armorer course, that was hosted by the Susquehanna Township Police Dept. This was our 1st course here, and we look forward to future courses. The training room was set up to allow plenty of table space. There room is equipped with a screen and projector that allowed us to show animated graphics of the weapons system and powerpoint of detailed pics of gun parts, especially when looking at finer detail things like machining, stress cracks & wear.

The student base was a mix of Law Enforcement Officers from all over Pennsylvania, Ohio, and some Feds.

Rifles represented in this course were SLR15, Colt, BCM, Stag, Sig Sauer, Ruger, Daniel Defense, DPMS, LWRC, Rock River, Bushmaster, Larue, POF, and a few custom builds.

Day-1 started the day by going through the course manual that all students are given. Students were supplied with their own set of basic tools that are necessary to do 95% of the work on their rifles (short of restocking and rebarreling, of which wrenches and sometimes fixtures are necessary), Slip2000 "EWL" Extreme Weapons Lubricant and #725 Cleaner Degreaser, etc. A short session of nomenclature was covered, at which time covered every feature and exterior piece of the rifle to include all the hidden design features that most people are not aware of, and everyone prepped the rifles for disassembly work. Everyone was taught the procedure series of checks that we recommend.

Everyone was taught our recommended way to field strip a rifle, and why we do it this way so as not to cause damage, premature wear or stress on anything. We covered maintenance of where and what to clean, and what needs lubrication to keep it running. We showed why not to use the firing pins as tools. We showed everyone our recommendation of how to remove fouling and why, and everyone got to use our methods.

The entire bolt carrier assembly was covered, to include inspections, maintenance, upgrades, 3 types of gas rings, and differences in finishing and machining. carrier key (gas key) installation and staking, ejector systems, etc. Everyone was introduced to the different types of gas rings. We went through what each types does, and their proper installation order. Bolts were fully gone through, which included extractors, extractor springs/inserts/O-rings. The ejectors were removed, cleaned, and inspected.

Note: We went through proper carrier key staking. Several people found their gas keys were lightly staked. We supplied everyone with a MOACKS and Sully Gas Key Staking Tools, everyone decided to use the Sully Gas Key Staking Tool and get things corrected.

We got into the lower receiver assemblies, starting with the fire control group (trigger group). We teach this in a building block format, starting with baby steps of getting things out and in, then build into how things work. Everyone learned how to install and remove things so you don't cause damage. We went through detailed inspections of all the sear engagement surfaces, spring types, single stage, and two stage trigger systems.

Note: One of the Colt M4's was found to have a broken trigger pin. This rifle also showed signs of heavy use and wear. The Officer who brought it stated that he had no idea when it was last inspected, and wasn't aware of the action spring (Buffer spring) ever being replaced. It is our opinion that the action spring should be replaced on a regular basis, and especially when you see signs of any stress or excessive wear, as fail to do so often leads to a gun beating itself up and parts getting out of spec and often times broken. The best thing you can do for an engine is change oil on a regular basis, so I apply this regular maintenance principal to firearms, as if you change the recoil springs on a regular basis you will usually see things last longer with less stress and abuse.

At the end of the day everyone put their rifles back together, making sure that everything was in proper working order.

Day-2 started with a review of everything that was covered on day-1, with some greater details and myths covered. We then went back into trigger groups in great details, covering single stage, 2-stage, good and bad triggers, differences and options in spring systems, diagnosing problems when semi-auto turns into burst, and showing the differences in quality of triggers that are on the market. Once done with semi-auto trigger systems, we went into select fire trigger groups covering full-auto and burst trigger groups, to include replacement and diagnosing and repairs when experiencing malfunctions.

Everyone stripped their lower receivers, which allowed a chance for further inspections, and we went through a session on troubleshooting. Once everyone was comfortable with the entire lower receiver assembly, the were put back together, inspected, and made sure everything is in proper working order.

After trigger systems, we went through the rest of the lower receivers. Everyone had collapsible stocks. We covered the proper mounting & gauging, and proper castle nut staking on the collapsible stocks, and there were a few that had to be remounted to get them properly indexed, and a hand full of them needed to be staked.

We then got into a session on the timing. This is where we cover proper cycling, covering what effects timing, and how & what happens when it is out or proper time, dwell time, suppressor issues, etc, and how to get things into proper timing. This also led us into piston systems. We covered how the piston system works, break down and maintenance of the system (Yes piston systems do get dirty and have to be cleaned and maintained), how to properly adjust for timing changed, and trouble shooting. We also covered dwell time, and how it pertains to cycling issues, and hopefully got the point across of why we do not recommend barrel lengths shorter that 11.5" on unsuppressed rifles. During the timing session, we showed examples of adjustable gas blocks, and we also showed the gas control system from https://www.riflespeed.com/, which we like as it is adjustable with a quick turn by hand to one of the 12 different settings, and is well built for durability.

We showed how suppressors are properly mounted and gauged. Several people took advantage of the bore gauges that we make, and checked their alignment on their rifles that had suppressors.

The last half of day-2 was spent on the upper receiver assembly. We covered barrel removal, mounting, fixturing, gauging & inspections. We show numerous ways to fixture a barrel into a vise, and our preference as to which fixtures/methods to use when and how. We showed how to mount, then properly torque and gauge the barrel system, which ensures it is in proper working order.

At the end of the day everyone put their rifles back together, everything was inspected and gauged to make sure it was in proper working order. Everyone did chamber inspections, checked & gauged the four gas seals, firing pin protrusion, trigger press, and headspace.

Here is a brief overview of a few things that were covered:
History of the Weapon
Cycles of Function
General Disassembly & Assembly
Identification of Common Problems and Parts
Nomenclature
Identification of Group Components
Semi, Burst, and Full Auto Parts and Conversions
Complete Armoring Disassembly / Assembly
Barrel Replacement
Cleaning and Maintenance
Sight and Distance Considerations
Ballistic Issues
Barrel: Twist, Length, and Profiles
Gas Systems & Piston Systems
Parts Interchangeability, including Brands
Headspace
Firing Pin Protrusion
Trigger Systems
Chamber Inspection and Issues
Troubleshooting, diagnosis & repair
Gauging, Inspections, Stress & Interval Issues
Accessories and Customizing
Tool Options and Selection
SOP/MOD Accessories and Additions

CY6
Greg Sullivan "Sully"
SLR15 Rifles
DefensiveEdge.com

(763) 712-0123
 
Top