AAR SLR15 AR15 / M16 / M4 / AR308 Armorer & Advanced Armorer Courses, Fridley MN

Greg "Sully" Sullivan

Established
Vendor
VIP
SLR15 RIFLES AR15 / M16 / M4 / AR308 ARMORER COURSE & ADVANCED ARMORER COURSE

When: June 21-24, 2022

Where: Fridley, Minnesota

We conducted a 2-day (16-hour) AR15 / M16 / M4 / AR308 Armorer Course, and Advanced Armorer Course that was hosted by the Fridley Police Dept. This was our fifth time teaching courses course at this location, and we look forward to more in the future. The training room offers great lighting, a large HDTV system that allowed us to project some powerpoint and animations onto.

The student base were Law Enforcement Officers from Minnesota, Wisconsin, North Dakota and Michigan.

Rifles represented were SLR15, Colt, Bravo Company, DPMS, Bushmaster, Sig Sauer, Rockriver, APF Armory, Windham, Daniel Defense, Aero Precision, Palmetto State Armory, Smith & Wesson, and a couple of custom configured rifles from parts kits.

Day-1 started with going through the course manual that all students are given. Students were supplied with tools, and shown what they are and give sources to obtain them. Everyone was also given some Slip2000 "EWL" Extreme Weapons Lubricant and #725 Cleaner Degreaser, etc. A short session of nomenclature was covered, at which time covered every feature and exterior piece of the rifle to include all the hidden design features that most people are not aware of, and everyone prepped the rifles for disassembly work. Everyone was taught the procedure series of checks that we recommend.

Everyone was taught our recommended procedure for field stripping a rifle and why. From there we got into a session on proper maintenance, showing what to clean, where to clean, and how to clean, and followed up with proper lubrication of where and why.

We went through armoring the bolt carrier assembly showing inspections, maintenance, upgrades, the three different types of gas rings, firing pins, extraction systems, ejectors, etc. Gas key staking was inspected, and we showed replacements & proper staking. We also covered bolts, materials, testing, and inspections.

Note: Several Officers found stressed ejector springs, and there were also two broken ejector springs. These were replaced with new ones. Ejectors should be pulled on an annual basis on all bolts, and more often of higher round count bolts, cleaned and inspected, and replaced as necessary.

Note: Several people found gas key screws that had light gas key staking where the stake marks were not touching the screws on, Bushmaster, Rockriver, DPMS, Palmetto and Anderson. We supplied people with a couple versions of the MOACKS and Sully Gas Key Stakers that we brought, that people put to good use and corrected things.

In the afternoon of day-1 we went through the lower receiver. We started with the fire control groups (trigger groups). These were removed and inspected. We covered single stage and two stage trigger systems. Everyone learned all the functions of the springs, pins, disconnectors, how the pins integrate to lock things in. We covered the safety selector system, and corrected several erosion issues. We also covered how to properly remove and install the auto sear. The last part of the day everyone reassembled their rifles, and performed a series of check to make sure they were in proper working order before they were done for the day.

Day-2 started with a review of all that was covered on day-1, at the same time we added more detail and dispelled some myths. The rest of the morning was spent back inside the lower receiver, looking at the trigger groups and receiver machining in greater detail. This detailed session allowed us to show bad factory parts, good quality of parts, single stage vs 2-stage, and how and why these may effect reliability, fail to fires, burst issues during semi-auto fire, etc. Once factory machined parts were gone through, we went through where people may alter parts to do a trigger job, and the issues with this. We finished out all assemblies and functions of the lower receiver and its parts, to include trouble shooting and variations and parts changes.

Stock systems were next. This class had mostly collapsible stocks. We showed both types of systems, how stock systems are mounted, gauged and properly indexed, then how the spanner nuts & castle nuts are staked. Many people took advantage of the tools and bench vises that we brought, and fixed their misaligned stocks, and lots of stocks had to be staked.

After lunch we went back into cycles of fire in greater detail, and then into the timing cycles. The timing was covered in greater detail, showing issues of guns cycling too fast or slow, stress, and set the tone for troubleshooting throughout the rest of the day. We also covered suppressors, timing issues, stress, maintenance, and mounting. We covered piston systems, there were a couple variations in class, which gave us the opportunity look show that these do get fouled up and require maintenance, and things do wear out.

The rest of the afternoon was spent on the upper receiver assembly. We went through the upper receiver, which included the forward assist, ejection port cover, sights & optics issues. Next was gas tube & piston issues, and how their longevity is related to proper barrel mounting. Gas tubes were inspected for stress and gauged to make sure they were in spec, this relates to barrel mounting.

We went through barrels, this included mounting & indexing, types of metals, finishing, longevity, harmonics, etc. Everyone was allowed to rebarrel their rifles or make adjustments. A couple of barrels were removed, and none of them were mounted correctly as the barrel nut on one was loose, another was off center, and all the barrels had been mounted dry (not meeting Milspec). All of the barrels that were removed, cleaned & inspected, pasted and remounted, torqued, and gauged for proper indexing before they left the class.

Once all the rifles were put back together, everything was inspected and gauged to make sure it was in proper working order. Everyone did chamber inspections, checked & gauged the four gas seals, firing pin protrusion, trigger press, and headspace.

Here is a brief overview of a few things that were covered:
History of the Weapon
Cycles of Function
General Disassembly & Assembly
Identification of Common Problems and Parts
Nomenclature
Identification of Group Components
Semi, Burst, and Full Auto Parts and Conversions
Complete Armoring Disassembly / Assembly
Barrel Replacement
Cleaning and Maintenance
Sight and Distance Considerations
Ballistic Issues
Barrel: Twist, Length, and Profiles
Gas Systems (Direct Gas Impingement & Piston)
Parts Interchangeability, including Brands
Headspace
Firing Pin Protrusion
Chamber Inspection and Issues
Troubleshooting, diagnosis & repair
Gauging, Inspections, Stress & Interval Issues
Accessories and Customizing
Tool Options and Selection
SOP/MOD Accessories and Additions


SLR15 RIFLES AR15 / M16 / M4 / AR308 ADVANCED ARMORER COURSE

Days 3 & 4: We started with a review of the standard course. Everyone was then tasked to do a complete disassembly of their rifles, to include barrel removal. Everyone did a complete disassembly of their bolt carriers. We inspected everything for erosion and corrosion. Examples of the different types of forged, cast, and MIM extractors were shown. We showed several examples of MIM extractors, failures, and steel cased ammunition issues. We showed several different types of finishes on extractors, and showed how these perform. We went back through all the different types of extractor springs, generations of inserts, and differences in springs and treatments, O-rings and D-rings. Ejectors were inspected along with their springs. Several examples of different ejector springs were shown, and how spring treatments and materials perform. Tuning ejection was also covered. We went into great detail about ejection port pattern, which many people think is strictly about over gassing issues, so we showed that there is many other variables that come into play that effect this and how to tune things if necessary or desired, and that in most cases it isn't something to be worried about as long as the rifle is ejecting the brass with good results for performance.

Firing pins were inspected for length, damage, wear, corrosion and erosion. We showed the evolution of the firing pin assemblies, and competition firing pins, and the why and how for these. We showed why it is our preference to use stock firing pins in battle rifles and not competition ones. Bolt and cam pins were inspected up close, noting erosion and stress. We passed out numerous examples of broken and stressed bolts and cams, and showed why this happens. We showed what types of testing that bolts and other parts can go through. We showed how to die test things, and showed several examples of where the die showed stress cracks, everyone took advantage of our equipment and tested their bolts. Bolt carriers were inspected closely, with attention to the machining and finishing. We showed a couple of examples of badly machined bolt carriers, and what their effects on the parts are.

We replaced several gas keys, to include the use of the MOACKS & Sully Gas Key Staking tools, and then showed our personal preference for counter-staking. We showed several examples of over-torqued gas key screws, and what problems happened from it. We showed several examples of damaged & plugged gas keys, and erosion from bad assembly work. We showed several different carrier key screws in both Allen and Torx style that are available, and showed which ones are better.

We had people swab out their barrels so we could do a close inspection and gauging. We showed how and when to use a borescope, and everyone was allowed to go hands on to view the entire internals of the barrel. We got a closeup view of the chamber, throat & lead areas, rifling, gas ports, muzzle erosion, etc. We supplied a couple of new barrels that had no erosion or fouling, which allowed everyone to get a close up look at machining, chrome vs non-chrome lining, parkerizing & nitride. Students then scoped their own barrels, noting fouling, erosion, and damage from things like cleaning procedures. We showed several examples of bent and warped barrels. We supplied people with muzzle erosion and barrel straightness gauges, which everyone inspected their barrels.

Note: One of the Colt M4's that as brought was found to have a loose barrel nut. This was removed, inspected, and remounted properly. It was built dry with no moly paste present. Barrel built dry is a very common thing we find in class, which the Milspec calls for moly paste.

We gauged the gas ports, noting different gas port sizes between makers and barrel types, a reference to common gas port sizes from various makers that are listed in the course material. We covered gas port erosion and its effects on the performance of the rifle, making note the differences we see in erosion and barrel finishes. We showed examples of gas ports that were drilled before and after barrel finishing. We brought a few barrels that had worn out gas ports and erosion, this allowed everyone to get a close up look with the borescope and gauges.

Crowns were inspected, and we showed examples of damage. We showed how to do crown repair, and a couple of barrels were cleaned up. Several barrels were heavily fouled at the crown, which will effect accuracy, these were cleaned off then inspected. Fouling build up inside of the flash hider/brake/comp was shown. All muzzle devices were put back on the barrels. We showed the difference in the split washer, crush washer, peel washer, and shims, and when & how to use them. Everyone was also shown the proper way to install and remove suppressor mounts.

Chambers were scoped with attention on the shoulder, throat & lead areas. We showed how chambers are cut, reamed, and finished. This lead to inspecting for headspace, different gauges and chambers were shown. We provide several types of chamber reamers, and showed where and how these are used. We moved into chamber casting, and discussed when and how this may be done. We allowed people to cast a chamber. This led us to show a few out of spec chambers and how these performed. We showed a chamber cast from a short barreled rifle from an agency that had the rifle blow up. This barrel had been blowing primers on Federal XM193, so the agency tried another ammo which blew up the rifle. When checked by the ammo makers, the chamber gauged at 5.56 NATO. When we casted the chamber, it was discovered that the chamber was off set to the bore, which is why it was over pressuring and eventually blew up, showing it was the machining that was at fault and not the ammo.

Next we moved into chamber polishing, how and why. We started with everyone viewing their chambers up close, then allowed them to polish them. Only one Officer took advantage of polishing his chamber, we did and before and after inspection and people could see a noticeable difference of the mirror shine and it being much more slippery to allow casings to come out easier.

We disassembled some upper receivers, then inspected the machining for stress, corrosion and erosion, and all parts were gauged to make sure things were in spec. When looking at machining on uppers, we see tolerances all over the place and usually finding more tolerance issues when compared to lowers. Charging handles were inspected breakage and stress. We showed several examples of badly machined uppers in the charging handle area, the problems this causes, and how to fix this. Barrel types, extensions, configurations, types of finishes, receiver types, front sight bases & gas blocks, and finishes were covered in the context of how they integrate. We showed why people need to use quality and the correct fixture when working with specific barrels and uppers during installation and other barrel work. Barrels were remounted and gauged for proper indexing. Barrel extensions and upper receivers were inspected and we showed how these must integrate correctly together. We also showed how to true the upper receiver face and why, of which several people took advantage of using the tools to do this on their uppers.

Lower receivers were disassembled, and we inspected the machining up close. We showed receivers that were machined so the trigger group was off center. We showed examples of the different methods that receivers are machined, and how the lower fit works in conjunction with upper receiver fit. We showed examples of receivers that used different sized hammer and trigger pins and why. This size difference also must correlate with the lower receiver machining and finishing. We showed why some students receivers were tougher to get pins in/out and why. All receiver holes were gauged, and we showed examples of what is the min/max specs for these and why. We showed several examples of receivers with oval shaped pin holes, why this happened, and why this is bad. There were several receivers in this class that were machined off center, which was causing stress to the fire controls and receiver.

Note: Several people found that the blemished receivers that they purchased as a bargain, had machining issues where things were out of spec, and machined off center.

Trigger groups were gone through in great detail. During our standard Armorer Course, we go into detail on good & bad triggers, machining and materials used, and their effects. We reviewed and added on, going back through single stage and 2-stage triggers, trigger jobs, and the differences in quality of materials used and machining. We provided a bunch of different trigger groups for everyone to go through. A sampling trigger groups from Colt, Larue, ALG, DPMS, Geisselle, LMT, Rock River, JP Enterprises, Palmetto State Armory, and Bushmaster were tried by everyone. Everyone was tasked with installing several different trigger groups to see their personalities and differences. When a trigger group didn’t work, we went through them together to show why and where the problem is. Everyone was also provided with full auto and burst groups. Once installed, everyone go to see what worked and how. When something didn’t work, we showed them why.

The last part of day-4 was spent on barrels and free float tubes. We showed the different ways that front sight bases are mounted, and the 3 types of pin that are most often used. We showed how front sight bases are indexed and mounted, and generally why front sight bases cannot be interchanged between barrels, and how the rear sights are designed to work with the front sight type and how this is integrated with the upper receiver.

We showed how we fixture a barrel and front sight base for mounting, drilling, and reaming. We allowed people to help ream and mount a few barrels. We showed how to repair some pin holes. We then moved into gas blocks, and showed several different styles of how these are mounted. We showed how to properly index these, countersink mounting screws, and lastly how the drill and pin them and why.

We showed traditional standard feed ramps, along with what people call the M4 feed ramps, and we also showed several different makers versions of M4 feed ramps, noting that there are differences between makers. We showed a collection of bad feed ramp machining, which caused feeding issues. Everyone checked how their feed ramps integrated, and we came across a few that needed cleaning up. Everyone was shown how to clean and polish feed ramps, and then we allowed them to do it.

At the end of the day, all rifles were reassembled and fully gauged to make sure everything was in proper working order.

Here is a brief overview of what was covered in this course:
Cycles of Function & Diagnosis of Issues
Complete Disassembly / Assembly
Identification of Common & Uncommon Problems and Parts
Identification of Group Components & Rare Parts/Configurations
Chamber Reaming & Polishing
Accessories & Upgrades
Barrel Replacement & Modifications
Internal Barrel & Chamber Inspections
Chamber Casting
Feed Ramps
Crown Repair
Detailed Maintenance
Sight and Distance Considerations
Ballistic Issues
Headspacing & Inspections
Trigger Jobs
Detailed Trouble Shooting & Repair
M16 & Burst Conversions & Problems Association
Free Float Barrels / Forends and Modifications
Gas Blocks & Front Sight Base (Pinning)
Flash Suppressors/Muzzle Brakes/Comps/Mounts
Tuning, Harmonics & Customizing
Custom Tools & Fixtures


CY6
Greg Sullivan "Sully"
SLR15 Rifles
TheDefensiveEdge.com

(763) 712-0123
 
Top